Our customer helpline number is 01206 823448
Colasgrip Resin (2 Part Mix)
Colasgrip Resin (2 Part Mix)
Colasgrip Resin (2 Part Mix)
Colasgrip Resin (2 Part Mix)
  • Colasgrip Resin (2 Part Mix)

Colasgrip Resin (2 Part Mix)

()

Colasgrip Resin is an extremely high quality 2 part resin, ideal for creating high performance, non toxic, high friction and colour surfacing. The resin is a two component thermosetting pigmented epoxy resin binder, usually used in conjunction with calcined bauxite or granite.

See the full description

Ask a question about this product

Name (required)

Company

Phone/Mobile Number (required)

Email (required)

Comments

Please can you reply to me via

 Telephone Email

SKU: ST2683 / 2681 / 2682 Category: Brands: .
000

Colasgrip is a quick to put down, durable, fuel, oil and salt resistant product designed to give excellent skid resistance to BS EN ISO quality and environmental procedures.
Due to the ease of use and it’s easy use with anti-skid materials, Colasgrip is ideal for the delineation of bus and cycle lanes, pedestrian crossings, junctions, bends, roadabouts, other hazard areas and even driveways!

Colasgrip can easily be applied by hand using the following equipment:
1 stirrer (low speed high torque drill fitted with helical stirrer)
squeegees (serrated edge “v-notch” and flat bed types 1 truck 2-3 operatives
Mobile generator
Mixing container

Download Datasheet Download Datasheet

Additional Information

Weight0.1 kg
Preparation
 
1) Prior to application of Colasgrip, ensure that surfaces are clean, sound and dry.
2) All dust, dirt and loose material should be swept from the surface.
3) If the surface is dirty or contaminated by oil or grease, it should be water jet washed or cleaned using a 2% aqueous solution of detergent applied over the whole surface. The surface should then be scrubbed vigorously with a stiff brush to remove contaminants, thoroughly washed with clean water and allowed to dry or dried with a hot compressed air lance.
4 ) Any damage to the surface or irregularity must be repaired properly before applying Colasgrip. New asphalt should be left for at least 4 weeks trafficking before applying Colasgrip. Spraygrip should not be applied to "fatted up" black top or multi layer surface dressings.
5) Ensure surface is completely dry and above 5°C.
6) If necessary the texture depth of the surface should be studied and measured to determine the consumption rate of the binder. Measurement should be carried out using the sand patch method.
 
Mixing
 
1) The A and B components (resin and hardener) may separate in the containers on storage. It is essential that each component is stirred using the low speed high torque drill fitted with helical stirrer for 2 minutes and re-dispersed properly before mixing together. Component A should be stirred first ensuring that the stirrer is cleaned before stirring Component B.
2) If coloured binder is required 1 sachet of pigment should be added to component B and mixed for 2 minutes until it is a uniform colour.
3) Empty the contents of the smaller container (A component) into the larger container (B component) for mixing and blending (if pack size will allow). If more convenient both components can be poured out and mixed in a plastic bucket. Add the A component to the B component in the bucket for best blending results.
4) Mix contents together using the low speed high torque drill fitted with helical stirrer.
 
Advised duration of mixing process - two minutes.
It is essential that all of the components from each container are mixed thoroughly with the other component. Ensure material from the bottom, sides and corners is mixed properly. Failure to mix the binder properly will result in poor strength and cure of the system.
 
5) In cold weather, store the binder overnight in a warm store. This lowers the viscosity of the binder and makes it easier to use. It may also be necessary to pre-warm the A and B components to 20ºC to help with pouring and blending. Please consult the Colas technical department for further advice on this.
 
Application
 
1) Place the aggregate to one side.
2) The temperature of the A & B components should be between +10°C and +35°C before mixing, with the ambient temperature range being between +5°C and +35°C.
3) The mixed binder should be poured out as uniformly as possible and distributed by squeegee with serrated edge (V notches) 5mm wide and 5mm deep at 5mm centres. Care should be taken to obtain an even coating without puddles or thinly spread areas. Application rate will depend on texture depth and will be between 1.3-2.0kg/m2.
4) The aggregate should be applied as soon as possible. Bags of aggregate are distributed along the length of the area to be covered. As the epoxy resin is applied the bags are split and the aggregate applied onto the binder to excess. The aggregate should be "broadcast" onto the surface and where necessary a flat bed squeegee can be used to even distribution. Rolling is not required Using 1-3mm aggregate the application rate is 10-12kg/m2.
5) After all of the areas have been covered with aggregate to excess, the material must be allowed to cure. The time it will take the material to cure will vary according to the surface temperature, but is typically 3 hours at 20 ºC .After completion the area should be swept to remove excess aggregate to leave around 7-8kg/m2 of aggregate on the surface. The excess aggregate may be collected and used again as long as it has not been contaminated.

Reviews(0)

There are no reviews yet.

Add a Review

Be the first to review “Colasgrip Resin (2 Part Mix)”